Dear Colleagues and Partners,
Meet the new version of the mobile user application Author Connect 1.19 for IOS and Android.
Previously, the user could configure AUTHOR-ALARM devices only if the COMPASS module was installed. Thanks to the Author Connect v.1.19 update, the user can now configure AUTHOR-ALARM systems (IGLA, IGLA ALARM, AUTOSTART, and KEYLESS BLOCK Pro) via Bluetooth. *
For IGLA and IGLA ALARM, the following settings are available:
- Anti-theft and security features
- Sensitivity of shock, tilt, and motion sensors
- The system's recognition range for keyfobs and smartphones
- Comfort features (automatic closing of windows and sunroof, and folding of mirrors)
- Anti-carjacking
- Control of the standard Start-Stop system.
You can configure AUTOSTART via Bluetooth:
- Set up engine autostart algorithms and conditions.
- Enable/disable comfort features (automatic closing of windows and the sunroof).
You can configure KEYLESS BLOCK PRO via Bluetooth:
- Anti-theft and security features
- The system's recognition range for keyfobs and smartphones.
Previously, one was able to configure those features only via the “service” button or using a PC via Author Flasher, which made them not very user-friendly. Now, using the new version of the Author Connect v.1.19 application, even an ordinary user can easily configure their devices directly via a smartphone without having to contact a service center. Just open Author Connect v.1.19 on your smartphone, get connected to your equipment via Bluetooth and configure it with just a few clicks.**
Just follow these steps:
1.Download and install Author Connect v.1.19 on your smartphone.
2.Launch Author Connect v.1.19 and click Bluetooth settings.
3.Switch the devices below into relevant modes:
- IGLA/IGLA ALARM — into the PIN Change mode;
- AUTOSTART — into the Firmware Update mode;
- KEYLESS BLOCK PRO — into the Firmware Update mode.
The service indication signal on the dashboard will be repeating once per three seconds.
4.In Available devices, devices available for connection will be displayed.
5.Select a device — it will get connected via Bluetooth and available settings will be displayed on the screen. Carry out relevant settings.
6.Turn off ignition.
The setup is complete.
Meet the new version of the mobile user application Author Connect 1.19 for IOS and Android.
Previously, the user could configure AUTHOR-ALARM devices only if the COMPASS module was installed. Thanks to the Author Connect v.1.19 update, the user can now configure AUTHOR-ALARM systems (IGLA, IGLA ALARM, AUTOSTART, and KEYLESS BLOCK Pro) via Bluetooth. *
For IGLA and IGLA ALARM, the following settings are available:
- Anti-theft and security features
- Sensitivity of shock, tilt, and motion sensors
- The system's recognition range for keyfobs and smartphones
- Comfort features (automatic closing of windows and sunroof, and folding of mirrors)
- Anti-carjacking
- Control of the standard Start-Stop system.
You can configure AUTOSTART via Bluetooth:
- Set up engine autostart algorithms and conditions.
- Enable/disable comfort features (automatic closing of windows and the sunroof).
You can configure KEYLESS BLOCK PRO via Bluetooth:
- Anti-theft and security features
- The system's recognition range for keyfobs and smartphones.
Previously, one was able to configure those features only via the “service” button or using a PC via Author Flasher, which made them not very user-friendly. Now, using the new version of the Author Connect v.1.19 application, even an ordinary user can easily configure their devices directly via a smartphone without having to contact a service center. Just open Author Connect v.1.19 on your smartphone, get connected to your equipment via Bluetooth and configure it with just a few clicks.**
Just follow these steps:
1.Download and install Author Connect v.1.19 on your smartphone.
2.Launch Author Connect v.1.19 and click Bluetooth settings.
3.Switch the devices below into relevant modes:
- IGLA/IGLA ALARM — into the PIN Change mode;
- AUTOSTART — into the Firmware Update mode;
- KEYLESS BLOCK PRO — into the Firmware Update mode.
The service indication signal on the dashboard will be repeating once per three seconds.
4.In Available devices, devices available for connection will be displayed.
5.Select a device — it will get connected via Bluetooth and available settings will be displayed on the screen. Carry out relevant settings.
6.Turn off ignition.
The setup is complete.